Bombas Vaciado de Bidones

Pump kit JUNIORFLUX

Pump kit JUNIORFLUX
Features and benefits Pump Type
– for filling, transferring or dispensing small amounts of acids, alkalis, deionized water, cleaning agents, photo developers
– sealless in the liquid section
– shaft in Hastelloy C
– impellor in ETFE
– outer-Ø 25 mm
– thread on outlet G 1 A (BSP 1″ male)
– ease of handling due to lightweight construction (2 kg)
– ergonomic handle for single-hand operation
– optimum carboy emptying due to ideal impellor design
F314 PP-25/19 in Polypropylene
Immersion length Motor Type
700 mm – Commutator motor 230 Watt, 230 Volt, 50 Hz, IP 24
– including power supply cable, 5 m long, and 2-speed switch for speed control
Accessories supplied with the pump
– Hose connector PP
– Flexible PVC hose DN 13, 1,5 m long
– 2 hose clips
– Lever tap PP, seal FKM

 

Pump kit Acids and alkalis

Pump kit Acids and alkalis
Features and benefits Pump Type
– for transferring acids and alkalis like boric acid, hydrochloric acid, hydrofluoric acid (diluted), phosphoric acid, and liquid fertilizers
– unique barrel pump design in PP throughout the world: a steel cored inner tube provides the ultimate in stability and extended service life of the mechanical seal – even at high temperatures
– sealed inner tube, the liquid being pumped cannot enter the inner tube
– suitable for transferring almost all liquid fluids
– optimum barrel emptying due to ideal impellor design
– to be stripped for cleaning with a minimum of effort
F 430 PP-40/33 in Polypropylene
Immersion length Motor Type
1000 and 1200 mm – Commutator motor Type F 417, 450 Watt, IP 24
– with power supply cable , 5 m long, and 3-pole plug
– compact design with optimal cooling and low noise level
Accessories supplied with the pump
– Hose connection PP
– Flexibel PVC hose DN 19, 2 m long
– 2 hose clips
– Quick action tap PP, seal FKM
– Compression gland PP

 

Pump kit concentrated acids and alkalis

Pump kit concentrated acids and alkalis
Features and benefits Pump Type
– for transferreing concentrated acids and alkalis like chromic acid, nitric acid, sulphric acid and sodium hypchlorate
– unique barrel pump design in PVDF throughout the world: a steel cored inner tube provides the ultimate in stability and extended service life of the mechanical seal – even at high temperatures
– sealed inner tube, the liquid being pumped cannot enter the inner tube
– optimum barrel emptying due to ideal impellor design
– to be stripped for cleaning with a minimum of effort
F 430 PVDF-40/33 in Polyvinylidenfluoride
Immersion length Motor Type
1000 and 1200 mm – Commutator motor Type F 458, 460 Watt, IP 55
– with power supply cable, 5 m ong, and safety plug
– totally enclosed, fan cooled motor design with special corrosion-resistant painting, making this model particularly suitable for use in corrosive, vapour loaden atmospheres
Accessories supplied with the pump
– Hose connection PVDF
– Chemical hose DN 19, 2 m long
– 2 hose clips
– Quick action tap PVDF, seal FKM
– Compression gland PP

 

Pump kit Petroleum products

Pump kit Petroleum products
Features and benefits Pump Type
– for transferring petroleum products like Diesel oil, fuel oil and hydraulic oil
– with mechanical seal
– optimum barrel emptying due to ideal impellor design
– to be stripped for cleaning with a minimum of effort
· F 430 AL-41/38 in Aluminium alloy
Immersion length Motor Type
1000 and 1200 mm – Commutator motor Type F 417, 450 Watt, IP 24
– with power supply cable, 5 m long, and 2-pole plug
– compact design with optimal cooling and low noise level alternatively:
– powerful commutator motor Type F 457, 800 Watt, IP 24
– with power supply cable, 5 m long, and 2-pole plug
– with no-volt release, compact design
– with optimal cooling and low noise level
Accessories supplied with the pump
– Hose connection AL
– 2 m flexible petroleum hose DN 25
– 2 hose clips
– Quick action tap AL, seal NBR
– Compression gland PP

 

Pump kit High flammability liquids

Pump kit High flammability liquids
Features and benefits Pump Type
– for transferring high flammability liquids like acetone, ethyl alcohol, methyl alcohol, toluene, xylene
– tested and certified according to Directive 94/9/EC-ATEX 100a, category 1/2, for use in Zone 0
– sealless in the liquid section
– safe dry running of the pump
– inner tube and helix shaped support bearings completely self-draining – thus preventing from any mixtures of liquids being pumped
– no contamination of the liquid being pumped by shaft lubricants
– optimum barrel emptying due to ideal impellor design
– to be stripped for cleaning with a minimum of effort
F 424 S-43/38 in stainless steel 316 L / 316 Ti
Immersion length Motor Type
1000 and 1200 mm – Commutator motor Type F 460 Ex, 460 Watt, II 2 G EEx de IIC T6
– with power supply cable, 5 m long, and safety plug
– explosion-proof to ATEX 100a, category 2, according to Directive 94/9/EC, EC-Type-Examination Certificate No. PTB 97 ATEX 1035
– robust double shell housing in aluminium, very low noise level
– improved ventilation system providing optimal cooling and ensuring an extended service life

alternatively:

– Air motor Type F 416 Ex, 470 Watt at 6 bar, II 2 G cp IIC T6
– explosion-proof to ATEX 100a, category 2, according to Directive 94/9/EC, PTB-Registration-No. 02 ATEX D022
– extremely light-weight and powerful motor, overload-proof
– easily variable speed control by adjusting either the air supply pressure or volume

Accessories supplied with the pump
– Earth ground wire, 2 m long
– Chemical hose kit DN 19, 2 m long, complete with swaged fittings in brass on both ends
– Quick action tap in brass nickel-plated, seal FEP/PTFE
– Compression gland PP, electrically conductive

 

Pump kit Universal applications

Pump kit Universal applications
Features and benefits Pump Type
– for transferring liquids in the following industries: food, cosmetics, pharmaceutical, paint and varnishes
– tested and certified according to Directive 94/9/EC-ATEX 100a, category 1/2, for use in Zone 0
– with mechanical seal
– optimum barrel emptying due to ideal impellor design
– to be stripped for cleaning with a minimum of effort
F 430 S-41/38 in stainless steel 316 L / 316 Ti
Immersion length Motor Type
1000 and 1200 mm – Commutator motor Type F 460 Ex, 460 Watt, II 2 G EEx de IIC T6
– with power supply cable, 5 m long, and safety plug
– explosion-proof to ATEX 100a, category 2, according to Directieve 94/9/EC, EC-Type-Examination Certificate No. PTB 97 ATEX 1035
– robust double shell housing in aluminium, very low noise level
– improved ventilation system providing optimal cooling and ensuring an extended service lifealternatively:- Air motor Type F 416 Ex, 470 Watt at 6 bar, II 2 G cp IIC T6
– explosion-proof to ATEX 100a, category 2, according to Directive 94/9/EC, PTB-Registration No. 02 ATEX D022
– very lightweight and extremely powerful motor, overload-proof
– easily variable speed control by adjusting either the air supply pressure or volume
Accessories supplied with the pump
– Earth ground wire, 2 m long
– Chemical hose kit DN 19, 2 m long, complete with swaged fittings in stainless steel on both ends
– Quick action tap in stainless steel, seal FEP/PTFE
– Compression gland PP, electrically conductive

 

Pumpen-Set 99,98 % barrel emptying

Pumpen-Set 99,98 % barrel emptying
Features and benefits Pump Type
– the safe and cost-efficient solution for transferring high value or hazardous liquids
– optimim barrel emptying, remains of less than 0,05 l
– tested and certified according to Directive 04/9/EC-ATEX 100a, category 1/2, for use in Zone 0
– with mechanical seal
– to be stripped for cleaning with a minimum of effort
F 425 S-41/34 in stainless steel 316 L / 316 Ti
Immersion length Motor Type
1000 and 1200 mm – Commutator motor Type F 460 Ex, 460 Watt, II 2 G EEx de IIC T6
– with power supply cable, 5 m long, and safety plug
– explosion-proof to ATEX 100a, category 2, according to Directieve 94/9/EC, EC-Type-Examination Certificate No. PTB 97 ATEX 1035
– robust double shell housing in aluminium, very low noise level
– improved ventilation system providing optimal cooling and ensuring an extended service lifealternatively:- Air motor Type F 416 Ex, 470 Watt at 6 bar, II 2 G cp IIC T6
– explosion-proof to ATEX 100a, category 2, according to Directive 94/9/EC, PTB-Registration No. 02 ATEX D022
– very lightweight and extremely powerful motor, overload-proof
– easily variable speed control by adjusting either the air supply pressure or volume
Accessories supplied with the pump
– Earth ground wire, 2 m long
– Chemical hose kit DN 19, 2 m long, complete with swaged fittings in stainless steel on both ends
– Quick action tap in stainless steel, seal FEP/PTFE
– Compression gland PP, electrically conductive

Type F 550 S with three-phase motor

Type F 550 S
Features and benefits Positive displacement pump – eccentric worm type
– recommended for low to high viscosity, pasty, but still free flowing products
– eccentric worm-drive pump with bearing flange in aluminium
– with mechanical seal or stuffing box
– low wear due to low pump speed
– vertical and horizontal use
– outer diameter of pump tube 50 or 54 mm
– Type F 550 SX.-50/21 for use in Zone 0, tested and certified according to Directive 94/9/EC – ATEX 100a, EC-Type-Examination Certificate No. PTB 99 ATEX 4050/4051 X
– smooth pumping with very little turbulences
– low wear, no valves, vanes etc.
– vertical and horizontal use
The pump is available in Immersion lengths
– Pump: stainless steel 316 L / 316 Ti (S)
– Stator: PTFE, NBR, CSM, FKM
700, 1000 and 1200 mm (other lengths on request)
Available drive motors The picture shows
– Three-phase motor 0,75 or 1,1kW, 930 or 700 min-1,
jet-proof to IP 55 or explosion-proof to ATEX 100a
– Air motor 0,5 – 1,8 kW, 1000 min-1 at 6 bar,
explosion-proof to ATEX 100a
Eccentric worm-drive pump Type F 550 S-50/21 with three-phase motor

 

 

Type F 550 GS with commutator motor Type F460 Ex

Type F 550 GS
Features and benefits Positive displacement pump – eccentric worm type
– recommended for low to medium viscosity products, up to max. 30.000 mPas (cP)
– lightweight and easy-to-handle eccentric worm-drive pump with planetary gear
– with mechanical seal or stuffing box
– low wear due to low pump speed
– low weight of complete pump and motor unit
– outer diameter of pump tube 50 or 54 mm
– Type F 550 GSX.-50/21 for use in Zone 0, tested and certified according to Directive 94/9/EC – ATEX 100a, EC-Type-Examination Certificate No. PTB 99 ATEX 4050/4051 X
– smooth pumping with very little turbulences
– low wear, no valves, vanes etc.
The pump is available in Immersion lengths
– Pump: stainless steel 316 L / 316 Ti (S)
– Stator: PTFE, NBR, CSM, FKM
700, 1000 and 1200 mm (other lengths on request)
The picture shows
Eccentric worm-drive pump Type F 550 GS-54/26 with commutator motor Type F 460 Ex

 

Type F 550 GS6 with three-phase motor Type F 403/4

Type F 550 GS6
Features and benefits Positive displacement pump – eccentric worm type
– recommended for viscous products up to max. 80.000 mPas (cP)
– lightweight and easy-to-handle eccentric worm-drive pump with planetary gear
– extremely smooth transfer operations with a speed of 210 min-1 or 420 min-1 only
– with mechanical seal
– outer diameter of pump tube 50 or 54 mm
– smooth pumping with very little turbulences
– low wear, no valves, vanes etc.
The pump is available in Immersion lengths
– Pump: stainless steel 316 L / 316 Ti (S)
– Stator: PTFE, NBR, CSM, FKM
700, 1000 and 1200 mm (other lengths on request)
Available drive motors The picture shows
– Single-phase AC motor with capacitor switch Type F 403/2
0,50 kW, 2850 min-1, jet-proof to IP 55
– Single-phase AC motors with capacitor switch Type F 403/4
0,30 or 0,55 kW, 1450 min-1, jet-proof to IP 55
– Three-phase motor Type F 403/4, 0,55 kW, 1450 min-1, jet-proof to IP 55
– Three-phase motor Type F 403/2, 0,75 kW, 2850 min-1, jet-proof to IP 55
Eccentric worm-drive pump Type F 550 GS6-50/21 with three-phase motor Type F 403/4

 

VISCOFLUX

VISCOFLUX
Features and benefits Frame-mounted total package including
– allowing the transfer of high viscosity, pasty, non-flowing products, like for example grease, ointment, paste, silicon, paint and varnishes, etc.
– especially designed for use with 200-Litre-Barrels
– smooth pumping by using gentle, progressive cavity pumping technology
– compact construction with lifting handlees for easy portability and quick assembly
– fast strip down for cleaning or sterilisation
– flexible lip seal with tight fit to the inside of the barrel ensures an optimum barrel emptying
– drive motors: three-phase or air motors in differing kW-ratings and speeds
– guide cylinder with follower plate in stainless steel and clamp connection to the pump
– flexible lip seal customized for barrel diameter
– two hydraulic rams in aluminium for lifting the pump and follower plate after barrel emptying
– pneumatic control unit for rams

 

Type F 520 S-50/45 with three-phase motor

Type F 520 S-50/45
Features and benefits High viscosity liquid pump – Archimedean screw type
– recommended for viscous products up to max. 20.000 mPas
– screw pump with bearing flange in aluminium
– very robust pump design
– with mechanical seal
– can be operated against a closed outlet
– outer diameter of pump tube 50 mm
– low wear, no valves, vanes etc.
– easy to strip down
– ideal for transferring free flowing fluids
The pump is available in Immersion lengths
– Pump: stainless steel 316 L / 316 Ti (S)
– Stator: stainless steel 316 Ti (S)
700, 1000 and 1200 mm
Available drive motors The picture shows
– Three-phase motors 0,75 – 3,0 kW, 2850 min-1, jet-proof to IP 55
– Air motors 1,0 – 2,6 kW, 3000 min-1 at 6 bar, explosion-proof to ATEX 100a
Screw pump Type F 520 S-50/45 with three-phase motor